Gas-suction precision seeder is a precision seeding machine commonly used at home and abroad. The common faults are mainly the following. First, the amount of volatile seed is not stable. (1) Causes of unstable seed volume (1) The suction pipe is damaged. For example, leaks, loose joints, cracks, etc., make the air pressure drop, the suction force decreases, and the seeds do not absorb, resulting in some or all of them. Missed broadcast. Mainly as a result of reduction in the number of individual ridge sowing, or missing broadcast. (2) Aspirating hoses are poor in quality, ageing, deterioration, or damage, leaks, or cracks due to improper storage, or the release of layers in the inner layer increases air flow resistance, resulting in lower air pressure, less adsorption of seeds, and reduced seed removal. Or completely missed. (3) The suction bearing on both sides of the suction fan is worn badly or is in disrepair for a long time or lacks oil for a long time, resulting in increased resistance, reduced speed, insufficient airflow and air pressure, and it is difficult for the seed to be adsorbed on the seed disc. This phenomenon occurs in the entire machine (all monomers) insufficient broadcast or completely missed broadcast. (4) The speed of the main engine (the tractor) decreases, or the power output shaft fails, causing the fan speed to drop and the air flow to be insufficient. (5) The drive system, such as the triangular drive belt, old, serious friction, elongation, loose strings, etc., cause the fan speed to drop. (6) Seed trays are deformed, rusted, or deformed due to improper storage or installation, so that the seed trays are not tightly contacted with the seed chambers, resulting in air leaks. Some or all of the seeds are not adsorbed. (7) Seed cleaning is not good, mixed with debris, the eyes of the seed plate hole blocked, causing leakage sowing. (8) The type of seed plate selected is improper, the hole (or hole) is too small, the air suction is too small, and the seed cannot be adsorbed or the amount of suction is small, resulting in missing broadcast or insufficient broadcast. 2, troubleshooting methods. When the monitoring personnel or the monitor sends a missed broadcast signal, stop the flame immediately and place the seeder on the floor (hanging type) to check the reason. If the connector is not firmly connected, it can be fastened again; if there is a small hole or crack, it can be patched with tape. If the hole is too large or the crack is too long, replace the new one. If there is a large delamination resistance on the inner wall of the gas pipe, replace the new one. Row seedlings or rows of seeding chambers can be tested for deformation, and new air leaks should be replaced after schooling. If the engine speed is normal and the air volume of the fan is still insufficient, the fan bearings must be inspected. . Second, do not sow 1, completely not sowing reasons. The seed sowing machine completely fails to sow in the pilot broadcast and operation, mainly due to serious wear or improper transportation and storage, resulting in deformation of the transmission parts, such as serious abrasion and deformation of the square shaft, sleeve, bevel gear, direction joint, seed metering device, etc., resulting in wind speed. The amount of wind is insufficient and it is not sown at all. 2, exclusion method. Carefully and thoroughly overhaul the seeder before the work, such as the square axis to be straightened, with the loose can be added to eliminate the gap gasket, wear serious to weld flatten after welding. Bevel gears with excessive wear must be replaced in pairs, and less serious wear can be added to the gap to eliminate gaps. The direction section can be filled with wear scars by push-welding and then flattened on the surface. After installation, it should be flexible. Seed meter to be replaced. Pay attention to the lubrication of the bushings and shafts and bevel gears during maintenance to reduce wear. Avoid collisions during transportation. Third, the sowing depth does not meet the agronomic requirements 1, the cause of the failure. The main reason is that the use of tools is too long and the wear of the parts is serious. If the opener is worn, it will be difficult to enter the soil and the open ditch will become shallow. After the earth-covered plate is worn, the amount of earth covering will be reduced, the thickness of the earth covering will be small and the depth of sowing will be shallow; the depth adjustment screws and adjustment nuts will be seriously worn out and buckled, and will be shaken at work. It will automatically change back and adjust the depth of adjustment; after the weakening of the tension spring, the amount of earth covering will decrease and the depth of sowing will also become shallower. 2, prevention and exclusion methods. Before the operation, serious inspections shall be carried out to verify the degree of wear of the above-mentioned components, especially the use of a seeder with a long service life. If the lead screw and adjustment nut are worn badly, replace the new nut with a double nut to prevent back-buckling. Apply grease to the screw and nut after work to prevent rust; if the tension spring is too weak, it can be Move the attachment point shortly or replace it with new one. After the season is finished, remove it and restore it to a free state. The surface must be coated with oil and rust-proof; the deformation of the soil-covered plate must be corrected, and the wear must be repaired or replaced with new ones. Corrosion. Openers also need to be repaired. In addition, during operation, it is necessary to prevent reversing the vehicle without lifting the machine; when the machine is dropped, it is necessary to “slow first and then slowly†to make the machine and the ground softly ground, and to slowly land on the road to prevent deformation and blockage. The transport seeder should be strictly prevented from colliding. It should be firmly fixed in the carriage and must not be driven at high speed. Source: "Peasant in Rural China" 2004.9
Vpro-Z
Vaping E Cigarette, E-Cigarette Starter Kits,E-Liquid ,E-Cigarette Atomizer
GSDGH , http://www.nbatomizer.com